Surgery Center Construction
Turnkey ASC and outpatient facility construction — from site selection to CMS certification. Operating rooms, sterile processing, and medical gas systems delivered on schedule.
UDGOK delivers turnkey ambulatory surgery center (ASC) construction for single-specialty and multi-specialty surgical groups across Oklahoma and Texas. ASC construction costs range from $350–$650 per square foot depending on specialty, OR count, and imaging requirements. We handle every specialized system — Class B/C operating room HVAC with 20+ air changes/hour, NFPA 99 medical gas installation (O2, N2O, medical air, vacuum, WAGD), sterile processing department (SPD) design, and CMS/AAAHC-ready infrastructure. Our healthcare construction team completes ASC projects 23% faster than the industry average.
Precision Execution
The $105 billion ambulatory surgery center market is reshaping healthcare delivery. More procedures are migrating from hospital ORs to freestanding ASCs — driven by better patient outcomes, lower costs, and faster recovery. But ASC construction demands a contractor who understands operating room HVAC classifications, sterile processing workflows, medical gas zone requirements, and CMS Conditions for Coverage. UDGOK builds surgery centers daily, delivering clinical infrastructure that passes inspection on the first attempt.
Discuss Your Project →What We Deliver
Operating Room Construction
Class B and Class C operating rooms with laminar airflow, 20+ air changes/hour, seamless wall/floor transitions, surgical lighting, and equipment ceiling booms.
Medical Gas Systems
NFPA 99 certified installation of oxygen, nitrous oxide, medical air, vacuum, and waste anesthetic gas disposal (WAGD) with zone valve boxes and alarm panels.
Sterile Processing (SPD)
Complete SPD design and construction with decontamination, clean assembly, sterile storage, and one-way workflow that meets AAMI ST79 and AORN standards.
Specialized HVAC
Positive-pressure ORs, negative-pressure isolation, precise temperature/humidity control, HEPA filtration, and dedicated air handling units per CMS requirements.
Emergency Power Systems
Life safety and critical branch emergency power, automatic transfer switches, UPS for critical monitors, and generator sizing for full surgical load.
Accreditation Readiness
Built to pass CMS, AAAHC, Joint Commission, and state health department surveys. Every system documented, labeled, and tested before your surveyor arrives.
How much does it cost to build an ambulatory surgery center in Oklahoma?
ASC construction costs vary significantly based on specialty mix, OR count, and facility complexity. Here are 2026 cost ranges for Oklahoma:
| ASC Type | Cost per Sq Ft | Typical Size | Total Budget Range |
|---|---|---|---|
| Single-Specialty (GI/Ophthalmology) | $350–$450 | 4,000–8,000 SF | $1.4M–$3.6M |
| Multi-Specialty (Ortho/ENT/General) | $450–$550 | 8,000–15,000 SF | $3.6M–$8.25M |
| Multi-Specialty with Imaging | $500–$650 | 10,000–20,000 SF | $5M–$13M |
| Spine/Total Joint ASC | $550–$700 | 12,000–25,000 SF | $6.6M–$17.5M |
These ranges include all MEP systems, medical gas, OR HVAC, sterile processing, and standard finishes. Site work, land, equipment, and furniture are additional. UDGOK provides detailed preconstruction budgets before you commit to a site or lease.
What are the key differences between ASC construction and standard medical office construction?
ASCs require significantly more complex infrastructure than standard medical offices. Key differences include:
- HVAC Classification: Operating rooms require Class B or C ventilation with 20+ total air changes per hour and positive pressure relative to corridors — far beyond the 6 ACH typical of exam rooms
- Medical Gas Complexity: ASCs need oxygen, nitrous oxide, medical air, vacuum, and WAGD (waste anesthetic gas disposal) — with zone valve boxes, master alarm panels, and NFPA 99 certification testing
- Sterile Processing: A full SPD with decontamination, clean assembly, and sterile storage — designed for one-way workflow to prevent cross-contamination
- Emergency Power: Life safety, critical, and equipment branch emergency power circuits with automatic transfer in 10 seconds — CMS mandated
- Infection Control: Seamless flooring, antimicrobial wall panels, sealed ceiling grids, and surgical-grade hand scrub stations at every OR entry
- Regulatory Burden: CMS Conditions for Coverage, state Medicare certification, and optional AAAHC/Joint Commission accreditation — each imposing specific construction requirements
What is the timeline for ASC construction from design to first case?
A typical ASC project follows this timeline from initial planning to performing the first surgical case:
- Site Selection & Feasibility (1–2 months): Location analysis, zoning verification, traffic/parking studies, and preliminary budget development
- Design & Permitting (3–5 months): Architectural design, MEP engineering, equipment planning, health department review, and building permit acquisition
- Construction (8–14 months): Shell construction, MEP rough-in, medical gas installation, OR finishing, SPD build-out, and systems commissioning
- Commissioning & Certification (1–2 months): Medical gas certification testing, HVAC balancing, fire alarm testing, CMS survey preparation, and accreditation survey
Total timeline: 13–23 months depending on project complexity. UDGOK's design-build delivery model can compress this by 3–4 months by overlapping design and early construction phases.
The
Process
Our proprietary construction methodology eliminates surprises, protects your budget, and accelerates your opening date.
Discovery & Analysis
We comprehensively assess your clinical program, target real estate, zoning conditions, and specific regulatory requirements.
Design & Engineering
Our teams coordinate full construction documents with integrated real-time cost tracking to prevent ballooning budgets.
Construction Execution
Self-performed mechanical systems and rigorous site management ensure total quality control and adherence to schedule.
Commissioning & Turnover
We validate all medical systems, manage inspections, and fully orient your administrative staff to the new facility.
Frequently Asked
Yes. We build every ASC to meet CMS Conditions for Coverage from day one. This includes specific requirements for OR ventilation, medical gas systems, emergency power, fire safety, infection control, and physical environment. We provide full documentation packages and coordinate all inspections required for Medicare certification.
Yes — this is one of our specialties. Converting existing medical office space into an ASC requires significant MEP upgrades including OR-grade HVAC, medical gas systems, emergency power, and sterile processing. UDGOK evaluates the existing building systems to determine feasibility and provides accurate conversion budgets before you commit.
A typical ASC requires oxygen (O2), nitrous oxide (N2O), medical air, surgical vacuum, and waste anesthetic gas disposal (WAGD). Each system includes source equipment, distribution piping, zone valve boxes, outlet stations, and master alarm panels — all installed and certified per NFPA 99 Health Care Facilities Code.
We implement Infection Control Risk Assessment (ICRA) protocols on every healthcare project. This includes negative-pressure containment barriers, HEPA filtration, sealed construction zones, dedicated debris removal paths, and air quality monitoring. For ASCs built within active medical facilities, we coordinate all work to prevent disruption to existing clinical operations.
Yes. Our preconstruction team coordinates with your equipment vendors to ensure proper infrastructure — electrical circuits, medical gas outlets, structural support, data connections, and equipment clearances — is designed into the construction documents from the start. This prevents costly change orders once construction begins.
UDGOK is a leading construction company in Tulsa, Oklahoma — delivering commercial, medical, dental, industrial, and retail projects across the Tulsa metro. Explore our complete guide to construction in Tulsa for costs, timelines, and building types.
Start Your
Project
We provide accurate feasibility analysis and cost modeling before you sign a lease. Contact our project directors today.